Flexible Resin (900 гр)

Set of 1800 gr !

The principle of operation:
Mixing ratio A100:B80
For example, for 100 grams of resin, you need 80 grams of hardener
The mixing time is 3 minutes, this is very important, if the resin is not well mixed with the hardener, then in some places the picture may not solidify!

Flexible resin. It is used to create flexible products. Forming a coating that is resistant to abrasion and resistant to high temperature. The resin is intended for moderate bending of products, for example, such as a soft cover for a notebook or the creation of bonfires and trays. Please note that the bending of the products should be moderate, otherwise it can lead to cracks and fractures. Over time, the product becomes less elastic. Finished product: it is not recommended to wash with abrasive detergents.

The recommended volume for better mixing of the components of the finished composition is 50 g.
Mixing table of component A and component B
To get the right amount of ready-made composition:
50 gr. = A 27 gr. + In 23 gr.
100 gr. = A 55 gr. + In 45 gr.
200 gr. = A 110 gr. + In 90 gr.
500 gr. = A 277 gr. + In 223 gr.
900 gr. = A 500 gr. + In 400 gr.
1800 gr. = A 1000 gr. + In 800 gr.

High temperature resistance up to 220 degrees (leaves no traces)

It has a memory effect, tightens and restores the surface, making it glossy again after exposure to hard objects
Resistant to shallow scratches
Aligns the surface
Saves the form
UV radiation for a long time.
Sudden temperature changes can affect the surface of the product, it can crack. We recommend storing the finished product at a temperature of 20-25 degrees away from sunlight
When working, it has almost no smell (after drying, there is no smell).
It may have a slight smell in the finished product (for example, if the product is flexible when it is bent). In a calm state, the smell is almost imperceptible, if only you bring it to your nose in a dense one, then you will feel it.
The working time with the composition is 25 minutes.
The polymerization time for the cast is 3 hours
Strength set of 56 hours

Appearance:
ATTENTION!!! A light yellow shade may have a Component A. When applied to the product with a thin layer of up to 5-8 mm, this shade is invisible in the work.

To avoid sticking of the product to the mold surface, we recommend:
1. Do not overheat the burner
2. If you are working for the first time, test on one mold
3. We recommend removing the finished product no later than 11 hours
4. Poorly mixed components: we recommend mixing very thoroughly for about 5 minutes! we mix it in one glass, then pour it into a new clean glass and mix it in it. then pour it into the first one and mix it again.
5. The recommended volume for better mixing of the components of the finished composition is 50 g
6. Use a good scale.
7. Do not leave in a draft
8. Do not create vibration during drying.

Calculation of the quantity.

Calculation of the composition for round moldovs ⠀
⠀
To find out the area of the circle, you need to multiply π by the radius squared.⠀
And, as with other shapes, multiply by the resin value 0.5 (to get a product with a height of 5 mm)⠀

For example, let's take the popular size of the bonfire 13 cm:⠀

6,5 * 6,5 * 3,14 * 0,5 = 67 g ⠀
⠀
For such a fire, I usually take 90-100g of resin.⠀
It turns out 4-5 mm in height. ⠀
⠀
Part of the fruit bowl or tray 30 cm:⠀
15 * 15 * 3,14 * 0,5 = 353 gr ⠀
⠀
For this size, I usually take 380 gr. Similarly, the height of 4-5 mm is obtained.⠀

Author of the article: @eve_afflatus

⠀
Again, do not forget about the stock. Let the resin remain better and you will fill in something small, than you will not have enough just a little bit to bring the work to the desired result.⠀

CHILDREN ARE NOT ALLOWED ! Strictly 18+
Pregnant women can not!!!
Do not take it orally!

Precautions: Avoid contact of unprotected skin and mucous membranes with the composition and dust formed during the grinding process, as this can cause moderate or severe skin irritation. When working, use protective clothing: glasses, a respirator, nitrile gloves, a cap or scarf, armbands, an apron. For additional safety, it is recommended to use protective creams and ointments.
Do not inhale dust from grinding, use a respirator and protective glasses when machining the finished product.
Do not use solvents to remove the composition from the skin. In case of contact with the skin, immediately remove the composition with dry wipes or a towel, then rinse the contact area with warm water and soap. After washing your hands, dry them with a disposable paper towel, and then lubricate them with a soft, greasy ointment based on lanolin vaseline or castor oil.
If a skin rash appears during work, stop working. If the problem persists when you resume working with the material, stop working with it and consult a doctor. In case of contact with the composition, immediately rinse your eyes with water for 15 minutes and consult a doctor. If any of the components or dust from sanding gets into your eyes, immediately rinse them with warm water. If after this you feel pain, burning in the eyes, seek help from a doctor.
Avoid swallowing the material and dust from grinding. Wash your hands thoroughly after work, especially before eating. If you have swallowed the epoxy resin, drink plenty of water and call a doctor immediately. When using the product, do not smoke, drink, or eat.
Allergy: Individual intolerance to the material and allergic reactions are possible, in case of their manifestation, immediately stop working with the material and consult a doctor. After the product is completely frozen, it does not emit any harmful substances, but there is still a process inside it that is invisible to you and me, so any product should rest for 1-3 weeks after curing, before contact with the skin in order to avoid allergic reactions, since it is all very individual.
Keep away from children, heating devices, at a temperature not exceeding 30°C. Store separately from food products.

ATTENTION!!!! A light yellow shade may have a Component A. When applied to the product with a thin layer of up to 5 mm, this shade is invisible in the work.

If you use a flexible resin as a finishing protective layer and cover the product with resin:
We warn you that such a product may eventually burst, crack or peel off.
To avoid this, we recommend:
Apply a protective layer on a "fresh" resin product, with our resins (thick and medium) this is after 12-15 hours (depending on the temperature and humidity). You can also check this point by pressing on the product, it should not be squeezed, but the prints will remain.
If you want to apply a layer on a finished product for a long time, we recommend that you walk with a fine sandpaper on the surface and then apply a thin layer of any ecpoxide resin (ready-made composition: resin+hardener mixed in the right proportions) to the surface of the product. After that, after 12-15 hours (depending on the temperature and humidity), apply a protective layer. You can also determine the appropriate moment for application by pressing on the product, it should not be squeezed, but the prints will remain.

1. due to poor surface preparation: the presence of moisture. It is impossible to work at high humidity
2. application on a glassy material (a long-created product)
3. application on an oily surface or with traces of oil, silicone, etc.
4. the surface is not degreased (use a tool that does not leave an oil film on the surface) the best is nephras
5. finished product: it is not recommended to wash with abrasive detergents. This can lead to peeling or cracks on the surface.
6. poorly mixed components, even if the product is frozen, peeling may occur over time due to poor mixing
7. overheating by the burner can also cause peeling after a few months (we recommend using a vacuum chamber to remove bubbles)
8. an error in the mixing proportions (the recommended volume for better mixing of the components of the finished composition is 50 g.) if you mix in a smaller volume, it can also lead to peeling of the surface over time. In a smaller volume, the components are worst mixed
9. the humidity of the air when applied to the product is not more than 35%
10. Sudden temperature changes can affect the surface of the product.